Showing posts with label space. Show all posts
Showing posts with label space. Show all posts

Tuesday, August 25, 2020

QO-100 ground station update

My previous post show tons of opportunities for improvement. The more I was thinking about those, the closer I came to my initial gut feel, i.e. using a helix as a feed for the up-link dish.
In fact, the helix was sitting on my desk for quite some time by now. I had doubts how to mount the helix in the first place, also matching appeared to be a big deal, without the help of any decent GHz-capable measurement equipment.

However, seen that no matter what I did, I could not really improve the performance of the up-link. Essentially, I spent two entire night to find the best position of the dish. (Night-time, so nobody is on the satellite, avoiding to disturb more senior users)

When listening to traffic on Es'hail 2, I often heard that operators switched from patch feeds to helical feeds for their up-links and reported better results with those. Was my gut feeling correct?!

So, today, I returned to trusting my gut feeling. So I removed the patch from the weird reflector / holder shown in the last post. I used a small piece of PCB to form a base, essentially a mount, for the helix. Yes, I could pretend that this was a carefully calculated matching strip for matching my 75Ohm SatTV cable to the helix, but it wasn't. I dimensioned and adjusted the PCB just such that the helix would be - more or less - in the center of the reflector.
note the remainders of glue where the patch was

Feel free to count the turns, which would result in a little of 6. My idea was, that I could always cut some off. It is much harder to cut wire on ;-)

The photo shows, it is night-time again. So, why not firing up the station and do some test transmissions?
And how right was my gut?!

lower beacon at 69dBuV

What a difference! My signal is now just 9dB weaker than the lower beacon!
Of course I had to do some side-band test. And yes, now I think I am QSO worthy.

The present setup still employs the "attenuator" made of about 10m of 70Ohm SatTV cable. So, as long as I still have not yet figured out how to build an outdoor unit (PSU,TX-converter and PA in a weather-proof box), I still will be able to do one or the other QSO.


Thursday, July 30, 2009

portable sat-comm station VHF PA

Well, not a great deal of technical skill involved here... I was able to locate an Yaesu FL-2025 linear amplifier which attaches to the back-side of my FT-290RII.

The FT-x90RII series appears not to be the most practical for satellite work, however, I now the series, I am one of only a few who actually like the handling and they have those neat clip-on linears. In a /p or /m setup, what counts in my view is having a box, as small as possible, in which all equipment fits uncluttered.
The series however has got a major down-side, tuning steps for European units are 12.5, 25 and 50kHz. Not exactly usable for the FM-sats as AO-51. However, there is help, with a simple mod one can change the FM-tuning steps to 5, 10 and 20kHz. More info on this: here (sorry, the important bit is written in German).

Now that Next step would be to build a crate for the two transceivers (290 and 790) and the linears, ensure sufficient cooling of the linears, provide a common power supply, feed preamp-supply to the antenna connectors, and some additional stuff for operating convenience.

Still a lot to be done, but now that all required gear is present, this work could be started any time.

Thursday, July 23, 2009

Eggbeater II (2)



Wow, that was easy. Nailed it all together. Actually, even though I found some RG62, without the delay line (some call that thing phasing), thus, linearly it will be polarized for now.The whole is mounted to a 40mm PVC pipe. No surprise here.
The surprise came when hooking it up the the MFJ analyzer. The SWR shows a minimum of 1.1:1, and, that actually takes place at 435MHz! K5OE did not promise too much. BTW, with AOL services closed, I hope Jerry's original page will show up again somewhere else.

Now that the standby RX-aerial is done, part two of the exercise will probably be to build TPMs (Texas Potato Masher) to be placed on a cheapoe rotator for TX.

The first setup is now more or less completed. Shopping for more PVC plumbing done.

Finally, I decided to leave in aerial linearly polarized. When remembering correctly, the difference would be 3dB. OK, this could make or break the link-budget, but than, this is supposed to be the first setup of its' kind that I made... collecting experience is a part of the game, I figure.

Now, lets wait for the first signals to appear!





Tuesday, July 21, 2009

UHF Eggbeater II


Having had the FT-736R inactive for sooooo looooong, it's time to think about putting together some aerials for space communications.

In the past I looked into the subject-matter before, but never actually found time and space to set things up. Thus faintly, my walnut recalled something called "The Eggbeater" and "The Eggbeater II", both, to me, are variants of the famous Turnstile. Some zick-zack thinking resulted in the decision to build an Eggbeater II for 70cm. Actually, I bought the material for the VHF version too.

If you are now puzzled what I am talking about, click here.

Here in Europe, we usually talk metric. The closest equivalent to #10 (AWG I assumed) copper wire I could find in my local hardware store was 6mm² copper wire.

The result, so far, can be seen in the image below. Bits and pieces still have to be assembled on a PVC pole. Before doing this, however, I first intend to test the aerial with both linear and RHC polarization.